What types of jumper wires are available?

We stock three main types: male-to-male, male-to-female and flat ribbon cable. Each suits different connection points on your board or module.

Which jumper wire should I choose for my project?

Match the wire type to the connectors on your boards and modules. If both sides have male pins, use male-to-female. If both sides have female sockets, use male-to-male. For many signals, use ribbon cable.

Length matters too. The 10cm wires are great for compact builds on a breadboard. The 1-foot ribbon cable gives you more reach for larger setups.

Pack size depends on how many connections you need. The 20-piece sets suit small projects, while 40-piece sets give you spares for complex circuits.

How much do jumper wires cost in Pakistan?

Prices are budget-friendly. The 10cm male-to-female set starts at Rs. 80, the male-to-male set at Rs. 90, and the 40-wire ribbon cable at Rs. 350. These prices were checked in October 2026.

We deliver nationwide across Pakistan with a flat-rate shipping of Rs 350. Whether you are in Rawalpindi or anywhere else, you can get these wires delivered to your doorstep.

Are these jumper wires compatible with Arduino, ESP32 and Raspberry Pi?

Yes. All our jumper wires use standard 2.54mm pitch, which is the spacing on Arduino, ESP32, Raspberry Pi and most sensors and modules. They plug directly into breadboards and pin headers.

No soldering is required for standard pin-header connections. This makes them perfect for prototyping, testing and school projects.

What is the difference between jumper wires and JST connectors?

Jumper wires are loose wires with pins or sockets on the ends, used for temporary connections on breadboards. JST connectors are small plastic connectors that crimp onto wires for more secure, semi-permanent connections.

We stock both. If you need to connect a battery or a sensor with a JST socket, you can use a JST connector. For quick tests, jumper wires are easier.

Can I use jumper wires for robotics and motor connections?

For low-current signals, yes. But for motors and high-current devices, use thicker wires to avoid voltage drops. Jumper wires are best for logic signals, sensors and small modules.

If you are building a robot, use jumper wires for control signals and separate motor wires for power. Always check the current rating of your wire.

Frequently Asked Questions

What is the length of these jumper wires?

The male-to-male and male-to-female jumper wires are approximately 10cm long. The ribbon cable is 1 foot (about 30.5cm). These lengths are ideal for breadboard projects and short connections between modules.

Do these jumper wires require soldering?

No soldering is needed for standard pin-header connections. The wires come with pre-crimped pins and sockets that plug directly into breadboards and headers. This makes them reusable and perfect for prototyping.

How many wires come in a pack?

The male-to-male and male-to-female sets are available in 20-piece or 40-piece packs. The ribbon cable has 40 individual wires. Choose the pack size based on how many connections your project needs.

Are these wires compatible with breadboards?

Yes, all our jumper wires fit standard breadboards with 2.54mm pitch. The male pins plug into breadboard holes, and the female sockets accept male header pins. This makes them versatile for any breadboard project.

What is the price of jumper wires in Pakistan?

Prices start at Rs. 80 for the 10cm male-to-female set, Rs. 90 for the male-to-male set, and Rs. 350 for the 40-wire ribbon cable. These prices were checked in October 2026. We deliver nationwide with flat-rate shipping of Rs 350.

Showing 1–15 of 34 resultsSorted by popularity

Jumper wires are the fastest way to connect components on a breadboard or between boards. We stock male-to-male, male-to-female and flat ribbon cables in the lengths and pack sizes students and makers use most.

All wires here fit standard 2.54mm headers, so they work with Arduino, ESP32, Raspberry Pi, sensors and robotics kits. No soldering needed for most setups.

Quick answer

What are jumper wires and which type should I buy?

Jumper wires are pre-terminated cables for solderless breadboard and header connections. Choose male-to-male for breadboard-to-breadboard, male-to-female for board-to-sensor, and ribbon cable for multi-wire runs. Prices start from Rs. 80, checked in October 2026.

0
0
Your Cart
Your cart is emptyReturn to Shop