,

Incubator Turning Tray timer Relay Module, 6-30V Trip Delay Circuit Breaker in Pakistan

Availability:

Out of stock


Product characteristics: 
  • Wide voltage (6 ~ 30V) power supply compatible with micro USB 5.0V power supply, easy to use;
  • The interface is clear and simple, powerful, easy to understand, it meets almost all your needs;
  • There is a key stop function (Stop key), with reverse polarity protection, reverse polarity does not burn;
  • Increases the sleep mode, allows, without any type of operation in 5 minutes, to turn off the monitor automatically; Any key to wake up;
  • You can set different OP CL LOP parameters that are independent of each other saved;
  • All configuration parameters are automatically saved off.
 
Product parameters:
  • Operating voltage: 6-30V support micro USB 5.0V power supply
  • Trigger source: high trigger signal (3.0V-24V) without common ground system to improve the anti-interference ability of the system (also self-shorting common ground)
  • Output capacity: can control DC or AC within 30v 5A within 220v5A
  • Quiescent current: 20mA operating current: 50ma
  • Time range: 0.1 seconds-999 minutes continuously adjustable;
  • Availability: more than 10 million times
  • Operating temperature: -40-85 Celsius;
  • Size: 6.2 * 3.8 * 1.7cm
  • With optocoupler isolation, enhanced anti-interference ability, industrial grade circuit boards, set the parameters after power failure memory forever.
  • Special Note: Relay outputs are passive contact, no-load output to control a disconnect function.
 
Product manual:
 
Operating mode:
  • P1: After the trigger signal, the relay becomes OP time, and then disconnected; At OP time, as follows
  • P1.1: Invalid signal activated again
  • P1.2: the resynchronization signal is activated again
  • P1.3: the reset signal is activated again, the relay turns off, stop the clock;
  • P-2: to the trigger signal, the relay after the shutdown time CL, OP relay driving time, after the count is finished, disconnect the relay;
  • P3.1: After the trigger signal to the relay has become OP time, CL time relay, then the operation cycle, for signal to the relay off, stop the clock once more within the loop; cycles (LOP) can be configured;
  • P3.2: After power without the trigger signal, the relay becomes OP time, CL time relay, operation cycle; Cycles (LOP) can be configured;
  • P-4: Signal hold function if the trigger signal timing is cleared, the relay stays on; When the signal disappears, after the OP relay timer disconnection; Timer period, then there is a signal, the time is cleared;
Setup time:
  • After setting the parameter values ​​on the mode selection screen with a short push button, select the time range;
  • Decimal points XXX, time range: 1 second to 999 seconds
  • X decimal point in ten, time range: 0.1 seconds to 99.9 seconds
  • XXX decimal full brightness, time range: 1 minute to 999 minutes
  • For example, if you want to set OP is 3.2 seconds, move the decimal point to ten, the digital display 03.2
  • Parameter Description: OP-time CL free time LOP cycles (1-999 times “.” Represents infinite loop)
  • These parameters are independent of each other, but each of these common mode parameters, for example, P1.1 set OP-time is 5 seconds, the user wants to switch to P1.2 mode, then enter P1.2 set the appropriate parameters, OP will be five seconds;
  • In the main interface (screen 000) Press the SET button will display OP (CL, LOP) and the corresponding time XXX;
  • If only the time mode (such as P1.1, P1.2, P1.3 mode) is activated, press the SET button to display only the OP and the corresponding time;
  • If the pattern has OP, CL, LOP (such as P3.1, P3.2 mode) Press the OP setting button and the corresponding time, CL and the corresponding time, LOP and the corresponding number will be displayed;
  • In the setting mode, the main interface parameters by briefly pressing the Setting button set in the current mode can easily view, very convenient!
 
Parameter settings:
 
  • First, determine the operating mode of the relay;
  • The relay working mode, in the main interface (when the module is powered on, the current working mode flashes (P1.1 default mode), then enter the main interface) “Press and hold the SET button for 2 seconds after launch “to enter the mode selection screen by pressing up, Down buttons to select the mode to be configured (~ P-4 P1.1);
  • After selecting the mode to be set (for example, P3.2) Press the set key to set the appropriate parameters, then the parameter to be set flashes (OP-time, CL off time, LOP cycles (“-” represents an infinite loop ) up, down to adjust the value, support long press (Rapid increase or decrease) and press (increase or decrease one unit); Adjust the parameter value with a short push button to select the decimal position, select the time range (corresponding time from 0.1 seconds to 999 minutes); Short press the SET key to set the next parameter of the current mode, the previous process;
  • After setting the parameters of the selected mode is good, press the SET button for 2 seconds after launch, the set mode will currently flash, and then return to the main screen, setting the parameters of success is very simple!
  • The main interface: in the relay does not work the status display “000” (no decimal point), with a decimal point below the relay status, very clear!
  • Mode selection screen: long press the set to enter. After completing the setting, press the SET key to exit and return to the main interface is very simple.

 

Stop key functions:

 
Relay activation mode:
  • On: internal OP-time relay enables driving;
  • Off: the relay prevents driving is always closed;
  • In the main interface, short press the STOP button to switch between on and off, the current in which the status will flash, and then return to the main screen. (This function is an emergency stop function, a closed key disconnect relay)
Sleep:
  • CP sleep mode: five minutes without any operation, the digital display automatically turns off, the normal operation of the program;
  • Normal od mode: The digital display is always open;
  • Press the STOP button for two seconds after release, to change CP and od state, in which the current state of flashes and then return to the main screen.

 

Package Include:

  • 1 x Incubator Turning Tray  Relay Module, 6-30V Trip Delay Circuit Breaker 

Best Online Shopping Website for Incubator Turning Tray  Relay Module, 6-30V Trip Delay Circuit Breaker Timer in cheap price in Islamabad, Karachi, Rawalpindi, Peshawar, Multan, Faisalabad, Quetta, and all over Pakistan.

590.00

Out of stock

Product characteristics: 
  • Wide voltage (6 ~ 30V) power supply compatible with micro USB 5.0V power supply, easy to use;
  • The interface is clear and simple, powerful, easy to understand, it meets almost all your needs;
  • There is a key stop function (Stop key), with reverse polarity protection, reverse polarity does not burn;
  • Increases the sleep mode, allows, without any type of operation in 5 minutes, to turn off the monitor automatically; Any key to wake up;
  • You can set different OP CL LOP parameters that are independent of each other saved;
  • All configuration parameters are automatically saved off.
 
Product parameters:
  • Operating voltage: 6-30V support micro USB 5.0V power supply
  • Trigger source: high trigger signal (3.0V-24V) without common ground system to improve the anti-interference ability of the system (also self-shorting common ground)
  • Output capacity: can control DC or AC within 30v 5A within 220v5A
  • Quiescent current: 20mA operating current: 50ma
  • Time range: 0.1 seconds-999 minutes continuously adjustable;
  • Availability: more than 10 million times
  • Operating temperature: -40-85 Celsius;
  • Size: 6.2 * 3.8 * 1.7cm
  • With optocoupler isolation, enhanced anti-interference ability, industrial grade circuit boards, set the parameters after power failure memory forever.
  • Special Note: Relay outputs are passive contact, no-load output to control a disconnect function.
 
Product manual:
 
Operating mode:
  • P1: After the trigger signal, the relay becomes OP time, and then disconnected; At OP time, as follows
  • P1.1: Invalid signal activated again
  • P1.2: the resynchronization signal is activated again
  • P1.3: the reset signal is activated again, the relay turns off, stop the clock;
  • P-2: to the trigger signal, the relay after the shutdown time CL, OP relay driving time, after the count is finished, disconnect the relay;
  • P3.1: After the trigger signal to the relay has become OP time, CL time relay, then the operation cycle, for signal to the relay off, stop the clock once more within the loop; cycles (LOP) can be configured;
  • P3.2: After power without the trigger signal, the relay becomes OP time, CL time relay, operation cycle; Cycles (LOP) can be configured;
  • P-4: Signal hold function if the trigger signal timing is cleared, the relay stays on; When the signal disappears, after the OP relay timer disconnection; Timer period, then there is a signal, the time is cleared;
Setup time:
  • After setting the parameter values ​​on the mode selection screen with a short push button, select the time range;
  • Decimal points XXX, time range: 1 second to 999 seconds
  • X decimal point in ten, time range: 0.1 seconds to 99.9 seconds
  • XXX decimal full brightness, time range: 1 minute to 999 minutes
  • For example, if you want to set OP is 3.2 seconds, move the decimal point to ten, the digital display 03.2
  • Parameter Description: OP-time CL free time LOP cycles (1-999 times “.” Represents infinite loop)
  • These parameters are independent of each other, but each of these common mode parameters, for example, P1.1 set OP-time is 5 seconds, the user wants to switch to P1.2 mode, then enter P1.2 set the appropriate parameters, OP will be five seconds;
  • In the main interface (screen 000) Press the SET button will display OP (CL, LOP) and the corresponding time XXX;
  • If only the time mode (such as P1.1, P1.2, P1.3 mode) is activated, press the SET button to display only the OP and the corresponding time;
  • If the pattern has OP, CL, LOP (such as P3.1, P3.2 mode) Press the OP setting button and the corresponding time, CL and the corresponding time, LOP and the corresponding number will be displayed;
  • In the setting mode, the main interface parameters by briefly pressing the Setting button set in the current mode can easily view, very convenient!
 
Parameter settings:
 
  • First, determine the operating mode of the relay;
  • The relay working mode, in the main interface (when the module is powered on, the current working mode flashes (P1.1 default mode), then enter the main interface) “Press and hold the SET button for 2 seconds after launch “to enter the mode selection screen by pressing up, Down buttons to select the mode to be configured (~ P-4 P1.1);
  • After selecting the mode to be set (for example, P3.2) Press the set key to set the appropriate parameters, then the parameter to be set flashes (OP-time, CL off time, LOP cycles (“-” represents an infinite loop ) up, down to adjust the value, support long press (Rapid increase or decrease) and press (increase or decrease one unit); Adjust the parameter value with a short push button to select the decimal position, select the time range (corresponding time from 0.1 seconds to 999 minutes); Short press the SET key to set the next parameter of the current mode, the previous process;
  • After setting the parameters of the selected mode is good, press the SET button for 2 seconds after launch, the set mode will currently flash, and then return to the main screen, setting the parameters of success is very simple!
  • The main interface: in the relay does not work the status display “000” (no decimal point), with a decimal point below the relay status, very clear!
  • Mode selection screen: long press the set to enter. After completing the setting, press the SET key to exit and return to the main interface is very simple.

 

Stop key functions:

 
Relay activation mode:
  • On: internal OP-time relay enables driving;
  • Off: the relay prevents driving is always closed;
  • In the main interface, short press the STOP button to switch between on and off, the current in which the status will flash, and then return to the main screen. (This function is an emergency stop function, a closed key disconnect relay)
Sleep:
  • CP sleep mode: five minutes without any operation, the digital display automatically turns off, the normal operation of the program;
  • Normal od mode: The digital display is always open;
  • Press the STOP button for two seconds after release, to change CP and od state, in which the current state of flashes and then return to the main screen.

 

Package Include:

  • 1 x Incubator Turning Tray  Relay Module, 6-30V Trip Delay Circuit Breaker 

Best Online Shopping Website for Incubator Turning Tray  Relay Module, 6-30V Trip Delay Circuit Breaker Timer in cheap price in Islamabad, Karachi, Rawalpindi, Peshawar, Multan, Faisalabad, Quetta, and all over Pakistan.

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Incubator Turning Tray timer Relay Module, 6-30V Trip Delay Circuit Breaker in Pakistan”

There are no reviews yet.